Introduction

E Series E 8:2

The E 8:2 has smart green credentials delivering low lifetime cost of ownership.

Features

800 W amplifier carrying 2 flexible output channels in a high power density 1 rack unit form factor saves rack space and system cost
Energy efficient with Energy Star certification for supreme green credentials and exceptionally low lifetime running costs
Flexible IntelliDrive permits delivering the 2 x 400 W at constant voltage 70 V or low impedance (2, 4 and 8 Ohms) on any channel
Asymmetric channel loading allows mixing and matching loads with different impedances to maximize overall system efficiency and inventory utilization
High efficiency amplifier with low power consumption and minimized heat generation lowers demands on the installations’ mains distribution and cooling systems
IDEEA outputs stage based on proprietary, state–of–the–art Class–D amplifier technology for superior performance
Comprehensive fail safe circuit protection ensures continued operation even under reduced operating conditions
Auto–standby and auto–power–on reduces power consumption to below 1 W in non–operating cycles
Rail Sense Limiter (RSL) greatly reduces signal clipping and ensures simple configuration for constant voltage and low impedance loads
Built in 50 Hz high pass filter selectable per channel available on rear panel switch
Per channel attenuation knob and signal LED on rear panel for simple commissioning
Efficient cooling with temperature controlled fan with front to back airflow
Aluminum front panel with power and temperature LEDs and per channel signal and limit LEDs
GPIO connector with power control and indication for further system integration
Balanced high–quality analog inputs and amplifier outputs on detachable screw terminals

Technical sheet

Specification

General

Number of amplifier channels	2
Max total output all channels driven	800 W
Peak output voltage per channel	100 V / 70 Vrms
Max. output current	16 Arms

Max output power (all channels driven)

2 ohms	400 W
4 ohms	400 W
8 ohms	400 W (requires the “70 V” mode for the RSL, “Lo–Z” gives 200 W)
16 ohms	290 W (requires the “70 V” mode for the RSL, “Lo–Z” gives 100 W)
70 V	400 W
100 V	Can deliver 400 W to a 100 V load tapped at 800 W

Performance

THD 20 Hz – 20 kHz at 1 W	<0,1%
THD at 1 kHz and 1 dB below clipping	<0,05%
Signal to Noise Ratio	>112 dBA
Channel separation (Crosstalk) at 1 kHz	>70 dB
Frequency Response	2 Hz – 40 kHz
Input Impedance	20 kOhm
Common mode rejection (CMR)	50 dB
Output Impedance	25 mOhm

Gain, Sensitivity and Limiters

Limit and gain switch defining limit and gain (per channel)	2 pos: Lo–Z and 70 V
VPL for 70 V mode	100 V
VPL for Lo–Z mode	56.6 V
Sensitivity for stated power into 4 Ohm in Lo–Z mode	4 dBu
Sensitivity for 70.7 V out in 70 V mode	4 dBu
Sensitivity for stated power into 2 Ohm in Lo–Z mode	1 dBu
Sensitivity for stated power into 8 Ohm in 70 V mode	2.1 dBu
Sensitivity for stated power into 16 Ohm in 70 V mode	3.7 dBu
Gain in 70 V mode	35.2 dB
Gain in Lo–Z mode	30.3 dB
Level adjustment (per channel)	Rear panel potentiometer, from –inf to 0 dB

Connectors and Buttons

Input connectors (per ch.)	3 – pin detachable screw terminals, electronically balanced
Output connectors (per ch.)	2 – pin detachable screw terminals
High–pass filter	Fixed at 50 Hz, switchable per channel
Power control	Can be used to go between standby and ON
GPI (power control input)	Contact closure type, 2–pin detachable screw terminal, controls the power state
GPO (power state output)	Contact closure type, 2–pin detachable screw terminal, for external monitoring of the power state
Cooling	Single fan, front to rear airflow, no filter required, temperature controlled speed

Power

Nominal voltage	100 – 240 VAC
Operating voltage	70 – 265 VAC
Standby consumption	<1 W
Mains connector	IEC inlet

Dimensions

W: 483 mm (19”), H: 44 mm (1 U), D: 276 mm (10.9”)

Weight

4.2 kg (9.3 lbs)

Finish

Dark grey aluminum front and black steel chassis

Downloads:

DRAWINGS:

Engineering Drawings

TECHDOCS:

A & E Specifications A & E Specifications, German Current Draw & Thermal Dissipation English Data Sheet Operation Manual English Quick Start Guide, All Languages Quick Start Guide, Chinese Quick Start Guide, Japanese

Recommended for you

Air 5Fan

ProLights

Beam moving batten, 5x40W RGBW/FC LED, pivot control, infinity pan/tilt, 16 kg

The new Aliseo loudspeaker system is the new challenge that Pequod Acoustics has undertaken, designing an elegant system in composite material using the highest quality and specialized 5 “units. The system has an horizontal, symmetrical, and extremely compact design in relation to the performance

ALTANO 18.1

Pequod

The Altano system is a long excursion acoustic suspension subwoofer consisting of 3 12” long–excursion woofers housed in three ovoid volumes structure connected and fused to form an extremely light and rigid monolithic structure. The total power of the system is over 2700 Watts, having high sensitivity (97 dB 1W/1m), with a total radiant surface equivalent to a 21–inch diaphragm.